新型着色材料——速溶色浆粉的测试与应用

介绍了通过初级颜料的润湿、研磨与分散、稳定处理技术,使助剂和树脂均匀地包裹在颜料表面,并通过特殊工艺制得水性和油性色浆粉,并赋予了很好的速溶性和分散性。     

COB LED自动在线点胶测试补粉机的研制

在COB(Chip On Board)LED光组件制造领域,点胶、测试和补粉关键工艺基本以手工或半自动为主。为了保证COB LED产品质量一致性、提高生产效率,研制了一种COB自动在线点胶测试及补粉一体机,实现点胶、测试、补粉生产工序的自动化生产。阐述了其工艺流程及设计总体方案,提出了荧光粉量修补方法,修正初次点胶量,实现动态调节,减少人工干预。经实验验证,该一体机可以提高点胶工艺的自动化程度,具有运行速度快、可靠性好、性能稳定等特点。     

Synthesis of photoluminescent SiC-SiOx nanowires using coal tar pitch as carbon source

SiC-SiOx nanowires (NWs) with core-shell and chain-bead structures were synthesized via a catalyst-free chemical vapor deposition (CVD) route without Ar gas, using silicon and coal tar pitch powders as raw materials. The SiC-SiOx NWs with sharp tips formed by solid-vapor between Si (s) and CO (g) or C (s) and SiO (g), liquid-vapor between Si (l) and CO (g), and vapor-vapor between SiO (g) and CO (g) growth process along the [111] direction. The NWs were several millimeters in length, and the average diameters of the chains and beads were 40–90 nm and 325 nm, respectively. The obtained NWs had good blue-green photoluminescence property owing to the stacking faults and amorphous SiOx. This novel CVD route is simple, low cost and suitable for large-scale production.     

The influence of sodium caseinate on the physical properties of spray‐dried honey

The aim of this work was to spray dry honey (rape and buckwheat varieties) with Arabic gum (AG) as a carrier alone or in combination with sodium caseinate (1% and 2% w/w NaCas) as a drying aid. Powder recovery ranged from 66.2 ± 0.7% to 75.8 ± 4.9%, and the values were significantly higher for samples containing NaCas. Powders were characterised by good flowability, the addition of NaCas had positive impact on this factor. However, the hygroscopicity of protein‐containing powders was higher, especially at 2% w/w of NaCas. Powders hygroscopicity was related to particle size: AG powder of the smallest particle size was the most hygroscopic, while the particle size did not affected flowability, which was strongly related to the feed solution composition. Based on the obtained results, it was concluded that the addition of 1% w/w of NaCas as a drying aid during buckwheat and rape honey spray drying with Arabic gum as a carrier is favourable, while the further increase of protein content does not give additional benefits.     

水提法提取—电感耦合等离子体质谱法测定婴幼儿配方奶粉中的碘

用水提取婴幼儿奶粉中的碘,亚铁氰化钾和乙酸锌盐析法沉淀蛋白,过滤后可以得到澄清处理液。用电感耦合等离子体质谱对提取样液进行测定,130Te作为内标物进行定量分析。该方法简便快捷,检出限为0.10 mg/kg加标回收率为90.8%~109%,相关系数0.999,精密度试验RSD2%。     

超细粉体抑爆装置瞬态喷射特征参数

在敞开空间开展了容积为2 L及5 L的超细粉体抑爆装置瞬态喷射参数研究，重点介绍了5种典型装配条件下的喷射性能，并对相关特征参数进行定量分析。结果表明：抑爆剂喷射所形成的超细粉体云幕特性由气体发生器装配结构和膜片开启压力共同决定，但两者之间必须恰当配置，作用在膜片上的能量份额较大时，膜片开启状态恶化，抑爆器腔体聚压不足，抑爆剂二次喷射严重，反之膜片不能正常开启。装配优化后的I型抑爆器在触发后10 ms内腔体聚压达到峰值，膜片破裂后5 ms内抑爆剂全部喷射，喷射动态性能较好，在第1个100 ms内扩散速度达到15 m/s，在第2个100 ms内扩散速度约13 m/s，0~1 000 ms内平均扩散速度约8 m/s，扩散过程较为连续，不存在二次喷射现象，喷射距离可达到7.5 m，抑爆剂质量分布呈渐进增长，产生的超细粉体云幕特征参数优良。Ⅱ型抑爆器两种装配的喷射表明：当抑爆装置中压力上升历程及压力峰值较为接近时，抑爆剂粉体喷射特性无显著差异。上述结论的可重复性得到了数百次喷射实验的验证。     

超细粉在内循环流化床中的流态化特性

在内径120 mm的半圆柱形内循环流化床中,以平均粒径387 nm的Ti O2为原料,考察了单独通入流化气、射流气和同时通入流化气和射流气三种流化方式下超细粉的流化特性以及射流气速对超细粉聚团尺寸的影响。结果表明:同时通入流化气和射流气时,流化气能促进粉体循环,消除环隙死区;高速射流能有效破碎聚团,显著减小聚团尺寸,从而使超细粉在环隙区与导流管之间形成稳定循环,小聚团在环隙区实现平稳流态化。随着射流气速的增大,聚团尺寸减小,粒度分布变窄,在射流气速分别为60,90,120,150 m/s的条件下,聚团平均直径分别为194,158,147,135μm。     

衍生化-富集-表面增强拉曼光谱法快速筛查奶粉中亚硝酸盐

目的 建立衍生化-富集-表面增强拉曼光谱法快速检测奶粉中亚硝酸盐的分析方法。方法 样品水溶液通过除蛋白、衍生化后，采用阳离子小柱PSY-001对衍生化合物进行富集，再使用表面增强拉曼光谱对样品中的亚硝酸盐含量进行定性检测。结果 7类不同奶粉，采用本研究所建立的方法进行检测，根据不同的批处理量，单个样品检测全过程只需3~15 min，定性检测限为0.4 mg/kg，远低于国家安全标准对亚硝酸盐的限量要求(2 mg/kg)。方法的灵敏度在96%～100%，特异性为100%，假阴性率为0%～4%，假阳性率为0%，相对准确度为98%～100%。结论 该方法操作简单、快速，易于掌握，适用于奶粉中亚硝酸盐的快速筛查。     

Impact of the SiC addition on the morphological,structural and mechanical properties of Cu-SiC composite powders prepared by high energy milling

The effect of the SiC content on the microstructural, mechanical, and magnetic properties of Cu(1 − x)SiC(x) composite powders (x = 0, 2, 10 and 15 wt%) prepared by high energy milling for 30 h was investigated. The results showed that Cu particles were severely deformed and formed plate like particles of different sizes, while SiC particles were fragmented and embedded in the Cu phase, thus, forming composite particles. As the SiC content increased, the average particle size decreased from 40.75 to 12.84 µm. Besides, XRD data showed a decrease in the crystallite sizes of the Cu phase (from 23.66 to 21.56 nm), accompanied by an increase in the lattice micro-strain (from 0.41 to 0.46%). Changes in the lattice parameters of the Cu phase were observed. The Vickers microhardness were measured in compacted powder samples and reached a maximum value of 135.22 HV for the sample with 15 wt% SiC. The samples showed hysteresis magnetic behavior at 300 K, and with a maximum saturation magnetization of 0.123 emu/g. The weak magnetic signal is mainly due to Co impurities present in the WC from the milling media.     

Mild hydrogen production from the hydrolysis of Al–Bi–Zn composite powder

The development of mild hydrogen-generating materials is of great significance to improve the working life of hydrogen–oxygen fuel cells. In this study, Al–Bi–Zn composite powders were designed by phase diagram calculation and then prepared via the gas atomization method. The results indicated that the conversion yield of Al–12Bi–7Zn (wt.%) powder reached 98% with stable hydrogen production within 280 min at 50 °C. When composite powder reacted with NaCl solution to produce hydrogen, the dormant period of the reaction process was significantly shortened, but the conversion rate was slightly reduced. Additionally, the evolution of powder morphology during the reaction was investigated. The results showed that the continuous cracking of the powder led to the continuous exposure of fresh Al to react.